Panasonic Aircon Error Codes – What You Need To Know

By Author: Coolcare
Total Articles: 9
Comment this article

Panasonic aircon, like most modern appliances, have error codes to help diagnose problems. If you notice an issue with your Panasonic aircon unit, you can refer to these error codes to get a better understanding of the problem.
Panasonic Aircon Error Codes
Here’s a list of some common Panasonic aircon error codes and their meanings:
1. U0 - Communication Error
Cause: This error typically occurs when there is a communication failure between the indoor and outdoor units. Solution: Check wiring connections and ensure there are no loose or damaged cables. Reset the aircon if necessary, or contact a technician if the issue persists.
2. U1 - Outdoor Unit Protection
Cause: This error code indicates a problem with the outdoor unit, possibly due to high-pressure protection or a refrigerant leak. Solution: Check the outdoor unit for obstructions or dirt. Ensure that the airflow is not blocked. If the issue continues, you might need to call a technician to inspect the refrigerant levels. View more
3. E1 - Room Temperature Sensor Error
Cause: The temperature sensor inside the unit may be ...
... faulty. Solution: Clean or replace the temperature sensor. If cleaning doesn’t solve the issue, a replacement may be necessary.
4. E2 - Coil Temperature Sensor Error
Cause: This error happens when there is a problem with the coil temperature sensor. Solution: Check if the sensor is clean and properly connected. If there’s still an issue, replacing the sensor may be required.
5. E3 - Outdoor Temperature Sensor Error
Cause: This error occurs when the outdoor temperature sensor is malfunctioning. Solution: Inspect the outdoor sensor for damage. If necessary, replace the sensor.
6. E4 - Abnormal Outdoor Unit Protection
Cause: Indicates an issue with the outdoor unit’s protection circuit, possibly due to motor failure or compressor malfunction. Solution: The outdoor unit may need to be checked for issues such as motor or compressor problems, which should be diagnosed by a professional.
7. F0 - System Fault
Cause: A general system failure is indicated. Solution: Try restarting the air conditioner. If the problem persists, it could be an electrical or mechanical failure, which will require professional repair.
8. F1 - Remote Controller Error
Cause: The remote control is not communicating properly with the unit. Solution: Replace the batteries in the remote. Ensure there are no obstructions between the remote and the unit, and check the remote’s functionality.
9. F3 - Low Voltage Protection
Cause: This occurs when the voltage supplied to the unit is lower than required. Solution: Check the voltage level. If it’s low, you may need to contact an electrician to fix the electrical supply issue.
10. F4 - High Voltage Protection
Cause: This error happens when the voltage is higher than normal. Solution: Again, check the voltage supply. If it's high, a voltage stabilizer or regulator may be needed to prevent further issues.
11. P1 - Drainage Error
Cause: This error occurs when the aircon drainage system is clogged or obstructed. Solution: Check and clean the drainage system. If the problem continues, contact a technician to inspect the unit further.
12. P2 - Refrigerant Leakage
Cause: A refrigerant leak in the system. Solution: If this error occurs, it usually requires a professional technician to fix the leak and recharge the refrigerant.
13. H1 - Indoor Fan Motor Error
Cause: Indicates a malfunction with the indoor fan motor. Solution: Inspect the fan motor for damage. If needed, a replacement of the motor may be required.
14. H2 - Compressor Motor Error
Cause: This error typically indicates a failure in the compressor motor. Solution: A professional technician should inspect the compressor motor and replace it if necessary.
15. H3 - Indoor Unit Protection
Cause: A protection mode for the indoor unit has been triggered. Solution: This could be due to overheating, poor airflow, or a system malfunction. Check for obstructions or dirt around the indoor unit.
General Tips:
Reset the Air Conditioner: For many error codes, simply turning off and restarting the air conditioner may help resolve minor issues.
Check Filters and Airflow: Poor airflow due to dirty filters or obstructions can lead to errors. Clean or replace filters as needed.
Power Supply: Ensure that the unit is getting the proper power supply. Inconsistent voltage can trigger errors.
If these solutions don’t fix the issue, or the error code persists, it's best to consult a certified Panasonic technician for more in-depth repairs.
Contact information:
Call: +65 90235452 (or) WhatApp us: https://wa.me/6590235452

11 Mandai Estate,
Singapore -729908
Mail ID: info@coolcare.com.sg

#airconinstallation #airconinstallationsingapore #splitairconinstalllation #airconinstallationsingaporeprice #airconinstallationprice #acinstallation #centralizedairconinstallation #bestairconinstallation #acinstallation #acinstallationsingapore
#AirconInstall#SingaporeAirconInstallation#installairconsingapore#commercialairconinstallation#airconinstallationguide#cheapestairconinstallationsingapore#singaporeairconinstallation#Panasonicairconerrorcode#PanasonicairconerrorcodeSingapore#BestPanasonicairconerrorcode